• Search Catalog

Cart Summary

Shopping Cart Empty

NEW AND HOT

Small Image
Add to Cart
Quantity On Hand: 1
Brand: Raspberry Pi
7" touch screen for all Raspberry Pi's (1B+ onwards, except Raspberry Pi Zero and Zero 2), 1280×720px resolution, 24-bit RGB display, powered directly by the host Raspberry Pi (requiring no separate power supply), supports up to five points of simultaneous multi-touch.
ID: 12679   Your Price: €94.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
The VCNL4200 is a powerful two-in-one sensor, with a proximity sensor that works from 0 to 1.5m (59 inches) and light sensor with range of 0.003 to 1570 lux. It's the longest-range IR distance sensor, other than the Sharp Analog distance sensors. It comes with EasyC/Qwiic/Stemma QT for easy I2C connectivity.
ID: 12674   Your Price: €11.50
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
The CH32V203G6 has a single 32-bit RISC-V core, running up to 144MHz, with 10KB SRAM and 32KB single-cycle Flash. There's also extras you expect: ADC, timers, USB device, UART, I2C and SPI. It definitely does not run CircuitPython or Micropython, and Arduino support is very early. It's definitely not good for beginners!
ID: 12675   Your Price: €8.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
This board features the CH9102F USB-Serial chip that can upload code at 3Mbit/s for fast development time. It also has auto-reset for Arduino/ATmega328 boards, fairly good driver support, and for 99% of use cases is a fine replacement of the FTR232, FT231x or CP210x series.
ID: 12676   Your Price: €8.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
Need more flash for your project? No problem, this little board has 16 MB of memory and can communicate over fast QSPI interface (you can use SPI too, see the instructions in the user guide).
ID: 12677   Your Price: €5.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Raspberry Pi
The board incorporates a quad-core 64-bit Arm Cortex-A53 CPU, clocked at 1GHz. At its heart is a Raspberry Pi RP3A0 system-in-package (SiP), integrating a Broadcom BCM2710A1 die used in the Raspberry Pi 3 with 512MB of LPDDR2 SDRAM. Raspberry Pi Zero 2 WH offers 2.4GHz 802.11 b/g/n wireless LAN and Bluetooth 4.2, along with support for Bluetooth Low Energy (BLE). This version has presoldered GPIO header.
ID: 12680   Your Price: €29.00
Small Image
Add to Cart
Quantity On Hand: 6
Brand: Raspberry Pi
Second version of Pico is based on a new RP2350 microcontroller which brings a higher core clock speed, double the on-chip SRAM, double the on-board flash memory, more powerful Arm cores, optional RISC-V cores, new security features, and upgraded interfacing capabilities, while retaining hardware and software compatibility with earlier members of the Raspberry Pi Pico series.
ID: 12650   Your Price: €8.20
Small Image
Add to Cart
Quantity On Hand: 1
Brand: Raspberry Pi
The Raspberry Pi AI Kit bundles the Raspberry Pi M.2 HAT+ with a 13 tera-operations per second (TOPS) neural network inference accelerator module built around the Hailo-8L chip, for use with Raspberry Pi 5. It provides an accessible, cost-effective, and power-efficient way to integrate high-performance AI.
ID: 12651   Your Price: €110.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
This board comes pre-programmed with seesaw peripheral code that will let it act as an "I2C to something" converter. It has 12x GPIO, 9x 10-bit ADC, 5x 8-bit PWM, 1x NeoPixel output, 1x interrupt, 1x LED, 127 byte EEPROM and two StemmaQT/Qwiic/EasyC I2C connectors. Works with 2-5 V power/logic.
ID: 12647   Your Price: €7.90
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
Finally, a way to get up to 4 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected I2C port with your command. Using it is fairly straight-forward: the multiplexer itself is on I2C address 0x70 (but can be adjusted from 0x70 to 0x77 using jumpers on the back) and you simply write a single byte with the desired multiplexed output number to that port.
ID: 12648   Your Price: €6.40
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
This board has 18 total 'I/O' pins, 10 columns and 8 rows, which can be arranged as a matrix of buttons for a total of 80 switches. Or you can use any subset as individual GPIO input or outputs. The nicest part of the keypad driver is that it has a 10-element event FIFO queue. Since it's I2C (StemmaQT/Qwiic/EasyC compatible) it's very easy to use with any microcontroller or computer.
ID: 12649   Your Price: €9.50
Small Image
Add to Cart
Quantity On Hand: 20
Board is based on Bluetooth 5.0 module (4.0 and 4.2 compatibile), working frequency 2.4 GHz, GFSK modulation mode, max output 4 dB, max transmission distance up to 60 m. It can be controlled via AT commands over UART and by default BLE can be used without configuration. Power supply 3.6-6V, dimensions 32.6x18.9 mm.
ID: 12641   Your Price: €4.20
Small Image
Add to Cart
No items available to ship
Brand: Copymaster3D
A thermoplastic elastomer with a hardness of 95A in Shore scale, 0.8 kg per spool.
ID: 12619   Your Price: €26.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Copymaster3D
PLA based filament that glows green in the dark and look like natural PLA in the light.
ID: 12635   Your Price: €25.00
Small Image
Add to Cart
Quantity On Hand: 6
Brand: Raspberry Pi
The power-management IC used on Raspberry Pi 5 integrates a real-time clock, and charging circuitry for a button cell which can power the clock while main power is disconnected. This Panasonic ML-2020 re-chargable battery, with a two-pin plug is suitable for connection to the battery connector on the Raspberry Pi 5 board.
ID: 12587   Your Price: €8.90
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Raspberry Pi
The Raspberry Pi M.2 HAT+ enables you to connect M.2 peripherals such as NVMe drives and AI accelerators to Raspberry Pi 5’s PCIe 2.0 interface, supporting fast (up to 500 MB/s) data transfer. It supports devices with the 2230 or 2242 form factor and it's supplied with a 16mm stacking header and threaded spacers, so it can be fitted to a Raspberry Pi 5 with the Raspberry Pi Active Cooler in place.
ID: 12588   Your Price: €21.50
Small Image
Add to Cart
Quantity On Hand: 3
This ESP32 based development board has become known in the maker community as the “Cheap Yellow Display” or CYD for short. It's main chip is an ESP32-WROOM-32 module, it comes with a 2.8-inch TFT resistive touchscreen LCD (240x320px), a microSD card interface, an RGB LED, and I/O connectors.
ID: 12571   Your Price: €20.00
Small Image
Add to Cart
Quantity On Hand: 18
Solid state relay module with 5V control logic and up to 240VAC/2A load with fuse. This is high level trigger module, SSR is ON when control signal is HIGH. Module dimensions: 34x25x22 mm.
ID: 12582   Your Price: €3.50
Small Image
Add to Cart
Quantity On Hand: 5
High accuracy photoacoustic CO2 sensor by Sensirion, typically 50ppm + 5%, measurement range 400-5000 ppm, -10~60°C and 0-100% RH. 3-5V logic and power, I2C communication, board size 13.4x21.6 mm.
ID: 12586   Your Price: €34.40
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Osmtec
The DM542T is a fully digital stepper driver with support for PUL/DIR mode, over-voltage and over-current protections, +18~50VDC input voltage, 5V/24V logic voltage selector (default setting 24V), pulse input frequency up to 200KHz, 8 selectable peak current settings (1.0-4.5 A) and 16 selectable microstep resolutions. Suitable for 2-phase and 4-phase motors, e.g. NEMA17, 23 or 24.
ID: 12602   Your Price: €38.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Osmtec
This bipolar NEMA 23 stepper motor with step angle 1.8deg and size 57x57x114mm. It has 4 lead wires 400 mm in length, each phase draws 3.5A, with holding torque 3.0Nm(425oz.in). Shaft length 24 mm, shaft diameter 10 mm, motor weight 1.6 kg.
ID: 12570   Your Price: €62.20
Small Image
Add to Cart
Quantity On Hand: 10
Brand: Makerbase
Big current stepper motor driver based on TMC2160 chip, max current 4.33 A, up to 64 microsteps, opto coupled signal, supports 8-40 V DC power supply, spread cycle or stelth chop working mode.
ID: 12584   Your Price: €19.00
Small Image
Add to Cart
Quantity On Hand: 4
Brand: PrimaCreator
PrimaValue PETG 1.75mm grey 1kg.
ID: 12563   Your Price: €21.00
Small Image
Add to Cart
Quantity On Hand: 1
Brand: PrimaCreator
PrimaValue PLA+ is stronger than standard PLA, making it ideal for functional prints and prototypes.
ID: 12566   Your Price: €21.00
Small Image
Add to Cart
Quantity On Hand: 6
Brand: Seeed Studio
Seeed Studio XIAO ESP32S3 Sense integrates a camera sensor, digital microphone, and SD card support. Combining embedded ML computing power and photography capability, this development board can be your great tool to get started with intelligent voice and vision AI.
ID: 12517   Your Price: €23.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Argon 40
Argon NEO 5 M.2 NVMe is an aluminium case for Raspberry Pi 5 that enables cooling using a fan, heatsink and passive cooling fins and offers support for M.2 NVMe drives with M-Key up to 2280 size. It can be used without top cover with easy access to a wide range of ports. Dimensions: 100x70x40 mm.
ID: 12521   Your Price: €54.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Adafruit
The LTR390 is one of the few low-cost UV sensors available with both ambient light and UVA sensing with a peak spectral response between 300 and 350nm. Works with both 3.3 and 5 V logic, comes with EasyC/Qwiic/Stemma QT conectors for easy I2C connecting.
ID: 12366   Your Price: €9.50
Small Image
Add to Cart
Quantity On Hand: 5
This optical fingerprint sensor can be used to scan fingerprint and it can send the processed data to a microcontroller via serial communication. All registered fingerprints are stored in this module (up to 127 fingerprints).
ID: 12509   Your Price: €19.00
Small Image
Add to Cart
Quantity On Hand: 3
Based on ESP32-WROOM-32U module, this board lets you connect external WiFi antenna via uFL/IPEX connector. In any other way, this is a classic ESP32 dev board based on dual-core Xtensa® 32-bit LX6 MCU with 4 MB SPI Flash, 802.11 b/g/n WiFi, Bluetooth 4.2 and BLE. It comes with soldered headers and micro USB connector, antenna is not included.
ID: 12514   Your Price: €12.00
Small Image
Add to Cart
Quantity On Hand: 10
This board is based on ESP32-C3-MINI, a 32-bit RISC-V single-core microprocessor with 4 MB integrated Flash, 802.11 b/g/n WiFi and Bluetooth 5 LE support, 15 GPIO pins and onboard RGB LED.
ID: 12515   Your Price: €7.50
Small Image
Add to Cart
Quantity On Hand: 1
Brand: Fiberlogy
A thermoplastic elastomer with a hardness of 40D in Shore scale, which may be printed at the speeds up to 45 mm/s (15-30 mm/s with Bowden extruder). This is 0.5 kg spool.
ID: 12518   Your Price: €31.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Polymaker
PolyLite™ LW-PLA is a special foamed PLA designed to print with similar settings as regular PLA but with half the weight. LW-PLA is already pre-foamed, which means it will not foam when extruded from the nozzle Hotend temperature 190 – 210˚C, bed temperature 30 – 50˚C.
ID: 12505   Your Price: €39.00
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Polymaker
PolySonic PLA is a revolutionary high-speed 3D printing filament, with its lightning-fast extrusion rate and exceptional layer adhesion you can ramp up the speed of your 3D printer up to 300 mm/s. Hotend temperature 190 – 210˚C (up to 100 mm/s) or 210 – 230˚C (100-300 mm/s), bed temperature 25 – 60˚C.
ID: 12506   Your Price: €36.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
This HUSB238 breakout plugs into the USB C cable and then over the CC lines will negotiate the PD request and commands. For example we can ask what voltages are available (the standard offerings are 5V, 9V, 12V, 15V, 18V and 20V.) and then pick the highest one. Or if you need a specific voltage it will specifically select that one.
ID: 12473   Your Price: €9.50
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Pimoroni
The NVMe Base is a PCIe expansion card for the Raspberry Pi 5. Add an M-key NVMe SSD (with support from 2230 to 2280) and mount it under your Raspberry Pi for a compact and fast storage solution. It is the ideal solution for turning your Raspberry Pi 5 into a file server, media center, reverse proxy, etc.
ID: 12500   Your Price: €21.50
Small Image
Add to Cart
Quantity On Hand: 6
Brand: Adafruit
The ESP32-S3 has arrived in QT Py format - with dual 240 MHz cores, 4 MB Flash, 2 MB PSRAM, WiFi/BLE support and native USB, this QT Py is great for powering your IoT projects. It has NeoPixel LED and Stemma QT/Qwiic/EasyC for easy I2C sensor connection. Program it using CircuitPython or Arduino IDE.
ID: 12501   Your Price: €19.60
Small Image
Add to Cart
Quantity On Hand: 1
Brand: RTL-SDR Blog
Software defined radio dongle by RTL-SDR Blog based on RTL2832U chip, with several improvements over generic brands including use of the R828D tuner, triplexed input filter, notch filter, improved component tolerances, a 1 PPM temperature compensated oscillator (TCXO), SMA-F connector, aluminium case with passive cooling, bias tee circuit, improved power supply, and built in HF upconverter.
ID: 12279   Your Price: €59.00
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Raspberry Pi
Raspberry Pi 5 builds on the phenomenal success of Raspberry Pi 4. In comparison with its predecessor, it delivers a 2-3x increase in CPU performance, and a significant uplift in GPU performance, alongside improvements to camera, display, and USB interfacing.
ID: 12481   Your Price: €124.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Intergalaktik
The ULX3S is a fully open source, compact, robust and affordable FPGA board equipped with a balanced spectrum of extra components and expansions. Onboard peripherals such as SDRAM, USB, Digital video out, FM/ASK antenna, ADC and DAC can make it audio/video powerhouse for signal processing and synthesis, motor control or SDR. If you are just starting with FPGA, you can also use the ULX3S as powerful Arduino and program it using Arduino IDE in seconds.
ID: 12470   Your Price: €144.00
Small Image
Add to Cart
Quantity On Hand: 1
Brand: Intergalaktik
The ULX3S is a fully open source, compact, robust and affordable FPGA board equipped with a balanced spectrum of extra components and expansions. Onboard peripherals such as SDRAM, USB, Digital video out, FM/ASK antenna, ADC and DAC can make it audio/video powerhouse for signal processing and synthesis, motor control or SDR. If you are just starting with FPGA, you can also use the ULX3S as powerful Arduino and program it using Arduino IDE in seconds.
ID: 12471   Your Price: €224.00
Small Image
Add to Cart
Quantity On Hand: 9
Brand: Soldered
easyC is a system for faster prototyping and easy connection between the components. However, some of the components have only one easyC port or you just want your cable managmenet made better. What to do in those cases? The easyC hub comes to the rescue! It has six connectors so you can easily expand your circuit. EasyC is fully compatible with Qwiic/StemmaQT.
ID: 12472   Your Price: €1.50
Small Image
Add to Cart
Quantity On Hand: 8
Brand: Raspberry Pi
The Raspberry Pi Pico WH is based on the Raspberry Pi RP2040 chip, but with wireless connectivity added, soldered headers and JTAG connector. Alongside RP2040, a Raspberry Pi-designed chip, which features two ARM Cortex-M0+ cores clocked at 133MHz with 256KB RAM, 26 GPIO pins, and a broad range of interfacing options, there is also Infineon CYW43439 wireless chip which supports IEEE 802.11 b/g/n wireless LAN and BT 5.2.
ID: 12457   Your Price: €12.00
Small Image
Add to Cart
Quantity On Hand: 1
Brand: Raspberry Pi
The new 27W USB-C Power Supply with Power Delivery (PD) will deliver a maximum of 5.1V, 5A enabling the Raspberry Pi 5 to power a wider range of peripherals. The total power drawn from the four USB ports on Raspberry Pi 5 is limited by default to a nominal 600mA; this limit is automatically increased to a nominal 1.6A when the USB-C PD Power Supply is detected.
ID: 12454   Your Price: €18.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Raspberry Pi
This red/white case for Raspberry Pi 5 is a refinement of the Raspberry Pi 4 case, with improved thermal features to support the higher peak power consumption of Raspberry Pi 5. It integrates a variable-speed fan, powered and controlled from the dedicated connector on the Raspberry Pi 5.
ID: 12455   Your Price: €15.00
Small Image
Add to Cart
Quantity On Hand: 7
Brand: Raspberry Pi
The Active Cooler provides an alternative cooling solution for users who wish to use their Raspberry Pi 5 under sustained heavy load without a case. It combines a large metal heat sink with a variable-speed fan, powered and controlled via the fan connector. Does not fit in the official Raspberry Pi 5 case.
ID: 12456   Your Price: €8.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Arduino
The Arduino Nano ESP32 is the first ever Arduino board based on a ESP32 microcontroller from Espressif, the NORA-W106 module from u-blox®. This module supports both Wi-Fi® and Bluetooth® (5.0 and above), making it an ideal device for IoT development. With USB-C® connector, 16 MB (128 Mbit) of Flash, support for MicroPython & Arduino IoT Cloud enabled, it is a very versatile development board in a standard Nano form factor.
ID: 12450   Your Price: €35.00
Small Image
Add to Cart
Quantity On Hand: 7
Brand: Adafruit
This is a high-quality CP2102N USB-Serial chip that can upload code at a blistering 3 Mbit/s, it has has auto-reset for Arduino/ATmega328 boards and the same RS-485 and GPIO support that the CP2104 has, making it 'drop in' replacement for discontinued CP2104 Friend.
ID: 12449   Your Price: €8.50
Small Image
Add to Cart
Quantity On Hand: 2
The Raspberry Pi 4 Retro Gaming Kit is the best way to create your very own retro gaming console and includes everything you need, including high-quality official Raspberry Pi accessories. RetroPie is already installed on the SD-card, the only thing you have to do is add your favourite games!
ID: 12448   Your Price: €145.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Arduino
Enhanced and improved, the Arduino UNO R4 Minima is armed with a powerful 32-bit microcontroller. The UNO R4 Minima maintains the same form factor, pinout, and 5 V operating voltage as its predecessor, the UNO R3. This ensures a seamless transition for existing shields and projects, leveraging the extensive and unique ecosystem already established for the Arduino UNO.
ID: 12434   Your Price: €27.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Arduino
The Arduino UNO R4 WiFi combines the processing power and exciting new peripherals of the Arm® Cortex®-M4 microcontroller with the wireless connectivity power of the ESP32-S3 from Espressif. On top of this, the UNO R4 WiFi offers an on-board 12x8 LED matrix, Qwiic connector, VRTC, and OFF pin, covering all potential needs makers will have for their next project.
ID: 12437   Your Price: €39.00
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Osmtec
This is bipolar NEMA 14 stepper motor with step angle 1.8°, holding torque 23 Ncm, 5 mm axis and motor size 35x35x42 mm. Each phase draws 0.5A at 7.5V, it has 4 wires (length 30 cm) with no connector.
ID: 12438   Your Price: €14.90
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Raspberry Pi
Raspberry Pi 4 Model B key features are a 64-bit quad-core Cortex-A72 processor, dual-display support at resolutions up to 4K, hardware video decode at up to 4Kp60, 4GB of RAM, dual-band 2.4/5.0GHz wireless LAN, Bluetooth 5.0, Gigabit Ethernet, USB 3.0, and PoE capability (via a separate PoE HAT add-on).
ID: 11599   Your Price: €85.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: E3D
Achieve high-flow results in the same form factor as a standard E3D Revo™ thanks to optimised internal nozzle geometry. High Flow Nozzles can be used with your existing 40W HeaterCores to maximise your flow rate with standard printing materials. 1.4 mm nozzles have a volumetric flow rate of 37mm³/s (based on PLA at 220 °C).
ID: 12410   Your Price: €59.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Polymaker
PolyTerra™ PLA and PolyTerra™ PLA+ are based on the same eco-friendly formula however PLA+ was optimized for better layer adhesion and overall strength. Printing temperature ranges from 190 °C to 230 °C (25-60°C for build plate).
ID: 12408   Your Price: €25.00
Small Image
Add to Cart
Quantity On Hand: 1
Brand: Polymaker
PolyTerra™ PLA and PolyTerra™ PLA+ are based on the same eco-friendly formula however PLA+ was optimized for better layer adhesion and overall strength. Printing temperature ranges from 190 °C to 230 °C (25-60°C for build plate).
ID: 12409   Your Price: €25.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Soldered (e-radionica)
Dasduino Lite is the right choice when you are limited with space, but still looking for capable controller. Based on Attiny1604 (20 MHZ, 16 KB), with USB-C port, Li-ion charger, CH340 USB-UART converter, RGB LED WS2812B, 12 GPIO pins (9 anlog) and easyC/Qwiic/Stemma QT connector - all this in only 38x26 mm. Operating voltage is 5 V, logic level is 3.3 V, there are no headers and it comes with USB-C cable.
ID: 12405   Your Price: €6.50
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Adafruit
Adafruit Feather RP2040 SCORPIO, designed specifically for NeoPixel (WS2812) driving but also good for various other PIO-based projects that want to take advantage of the Feather pinout with 8 separate consecutive outputs (or inputs). 264KB RAM lets you drive thousands of NeoPixels and run your main program uninterrupted, all at the same time!
ID: 12399   Your Price: €24.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
Adafruit PiCowbell DVI Output for Pico is in stock and ready to display images and graphics from a microcontroller directly to an HDMI monitor or television! Note it doesn't do audio, just graphics.
ID: 12400   Your Price: €11.60
Small Image
Add to Cart
Quantity On Hand: 1
Brand: Adafruit
This little lipo charger is designed to fit onto the back of any QT Py board, and make it easy for portable powering. Simply plug any standard 3.7V/4.2V lithium polymer or lithium-ion rechargeable battery into the JST plug on the end. When powered by the USB port on the QT Py, the charger kicks in and will charge up the battery at 200mA max rate.
ID: 12401   Your Price: €8.25
Small Image
Add to Cart
Quantity On Hand: 19
Mini solar panel, 12V 150mA 1.8W, without wires, 110x110 mm.
ID: 12392   Your Price: €8.00
Small Image
Add to Cart
Quantity On Hand: 25
Input voltage 12 V, output volatage 4.2 V, max. charging current 2 A, PWM switching frequency 300 KHz, working temperature -40 °C to +85 °C, dimensions 45x20x9.5 mm.
ID: 12393   Your Price: €7.50
Small Image
Add to Cart
Quantity On Hand: 23
This board allows you to turn on and off, and control the speed of motors or micro pumps or the brightnes of LED lighting. Input (3.3-20 VDC) and output (3.7-27 VDC, up to 10 A) are completely isolated, PWM frequency: 0-20KHz, board size: 22.7x36.8 mm.
ID: 12394   Your Price: €4.90
Small Image
Add to Cart
Quantity On Hand: 20
This is a classic Arduino Nano V3 compatible board based on ATmega328 chip (32KB flash, 2KB SRAM, 1KB EEPROM, 16 MHz clock) with 5V logic level, 14 digital I/O pins (6 PWM) and 8 analog inputs. It comes with soldered headers and USB-C Type connector.
ID: 11069   Your Price: €11.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Raspberry Pi
The standard Raspberry Pi Camera Module 3 is a compact camera from Raspberry Pi with a 66 degrees field of view. It offers an IMX708 12-megapixel sensor with HDR, and features phase detection autofocus.
ID: 12370   Your Price: €42.00
Small Image
Add to Cart
Quantity On Hand: 7
This kit contains aluminum chasis, four motors and four omnidirectional (AKA mecanum) wheels with the mounting screws set.
ID: 12353   Your Price: €25.00
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Adafruit
This kit uses electromagnetic fields and inductive coupling to pass power through the air to light up little LEDs soldered onto coils. No wires needed! Each kit comes with one inductive coil connected to driver board (you'll need a 5V/2A power supply to power it - mobile phone charger will do) and ten small LED inductors in an assortment of colors (two each of white, blue, yellow, green, and red).
ID: 12281   Your Price: €26.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Adafruit
This kit uses electromagnetic fields and inductive coupling to pass power through the air to light up little LEDs soldered onto coils. No wires needed! Each kit comes with one inductive coil connected to driver board (you'll need a 24V/2A power supply to power it) and ten large LED inductors in an assortment of colors (two each of white, blue, yellow, green, and red).
ID: 12282   Your Price: €49.50
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
This board allows you to use I2C over long cables - up to 3m @ 400 KHz and up to 30m @ 100 KHz via Ethernet cable! Just connect it to your I2C bus at the beginning of the chain, no special firmware, software, or configuration required. Runs with any bus voltage, from 1.6V to 5.5V and up to 400 KHz SCL speed, with cables up to 4000pF.
ID: 12294   Your Price: €15.00
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
The PiCowbell Proto is the same size and shape as a Pico, and is intended to socket underneath to make programming and sensor connectivity easy. Reset button? Yes! STEMMA QT/Qwiic/EasyC connector for fast I2C? Indeed.To keep things flexible, this PiCowbell does not come with headers: you choose which configuration suits you best, you can even solder Pico directly to the board.
ID: 12296   Your Price: €3.80
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Seeed Studio
XIAO RP2040 is an Arduino-compatible microcontroller featuring the Raspberry Pi RP2040 chip. Its signature values of high performance, low cost, ease of use, and tiny thumb size make it perfect for TinyML, smart wearable devices, and IoT projects.
ID: 12266   Your Price: €8.25
Small Image
Add to Cart
Quantity On Hand: 8
ToF distance ranging sensor, 40 mm to 4 m, 3.3-5 V power and logic, I2C communication, dimensions 10x25x5 mm.
ID: 12269   Your Price: €12.00
Small Image
Add to Cart
Quantity On Hand: 17
This module lets you control up to 16 servo motors or any other kind of PWM outout over single I2C connection. It supports both 3.3V and 5V logic, has 12-bit resolution for each output and adjustable PWM frequency up to 1.6 KHz.
ID: 12271   Your Price: €13.00
Small Image
Add to Cart
Quantity On Hand: 34
Expansion and power shield for 30-pin ESP32 boards, USB-C and Micro 5V inputs and 6.5-16 V DC jack input, SGV (Signal-Ground-Voltage) 3-pin output for all GPIO pins with jumper selectable voltage (3.3 or 5 V power) and I2C extended interface (2 groups). Dimensions 68.6x53.4 mm.
ID: 12280   Your Price: €3.50
Small Image
Add to Cart
Quantity On Hand: 7
Brand: Soldered (e-radionica)
Dasduino CORE is based on Atmel Atmega328P microcontroller we all know and love. It has 14 digital and 6 analog pins, which is plenty for almost all projects. It comes with a USB Type-C connection and is 100% compatible with the original Arduino boards and Arduino IDE.
ID: 12258   Your Price: €10.50
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Soldered (e-radionica)
The APDS-9960 is a small sensor that measures four things at once. It is possible to recognize the movements you make in front of it (up, down, left, right) and it can identify the vicinity of the object, so you have two more movements: to the sensor and from the sensor. In addition, it has an ambient light sensor and a color sensor which gives red, green, and blue (RGB) colors as output.
ID: 12250   Your Price: €6.50
Small Image
Add to Cart
Quantity On Hand: 2
Brand: BBC micro:bit
The BBC micro:bit V2.2 is a pocket-sized computer that introduces you to how software and hardware work together. It has an LED light display, buttons, sensors and many input/output features that, when programmed, let it interact with you and your world. Micro:bit V2.2 with sound adds a built-in microphone and speaker, as well as an extra touch input button and a power button.
ID: 12202   Your Price: €24.00
Small Image
Add to Cart
Quantity On Hand: 1
Brand: E3D
Smaller, lighter, REDDER. Say hello to the Revo Voron, the HotEnd of choice for Voron 3D printers. The Revo-compatible cold side was developed in collaboration with Team Voron. Boost your Voron 3D printer with RapidChange capabilities so you can change nozzles without tools or hot tightening!
ID: 12164   Your Price: €108.04
Small Image
Add to Cart
Quantity On Hand: 3
Brand: DFRobot
The Geiger counter can only detect ionizing radiation, such as nuclear radiation, X-rays, cosmic rays, etc. This product is not a professional measuring instrument and is only suitable for principle research and teaching demonstration. Not for use in radiation dose measurement that directly affects personal safety.
ID: 12094   Your Price: €97.00
Small Image
Add to Cart
Quantity On Hand: 13
Brand: Adafruit
The AHT20 is a nice but inexpensive temperature and humidity sensor from the same folks that brought us the DHT22. You can take sensor readings as often as you like, and it uses standard I2C so its super easy to use with any Arduino or Linux/Raspberry Pi board.
ID: 12016   Your Price: €7.30
Small Image
Add to Cart
Quantity On Hand: 7
Brand: Adafruit
This RFID tag is really unique: it works with mobile phones just like other RFID tags, but you can reprogram it over I2C. The tag shows up as an ISO/IEC 15693 (13.56MHz) chip which is readable by phones and tablets. Note that the most popular hobby RFID reader/writer chips like the PN532 do not support ISO15693, but both Apple and Android phones can be used to read the tags with success.
ID: 12017   Your Price: €6.40
Small Image
Add to Cart
Quantity On Hand: 34
Analog output capatitive soil moisture senzor, output voltage 0~3 VDC, operating voltage 3.3~5.5 VDC, with Gravity 3-pin connector and Gravity to Dupont 3-pin cable. Dimensions 98x23 mm.
ID: 11995   Your Price: €2.50
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Micro Swiss
All metal hotend with thermal heat break made from titanium alloy which has a well-defined melt zone. It fits most of Creality 3D printers (see full description for detailed list of compatible printers), no modifications on your 3D printer necessary.
ID: 11971   Your Price: €66.10
Small Image
Add to Cart
Quantity On Hand: 9
One of the smallest ESP32 development boards available, it's pinout is compatible with ESP8266 based D1 Mini board, so D1 shields can be used with this board too. Comes with female pin header set (not soldered), including the one pair with extra long pins for shields.
ID: 11918   Your Price: €13.00
Small Image
Add to Cart
Quantity On Hand: 3
Brand: Micro Swiss
This is MK8 style nozzle, it is made from a 360 brass base material and plated with TwinClad XT coating. TwinClad XT is a nickel composite coating designed for very low friction. This coating is also very hard and abrasion resistant. If you are working with abrasive Carbon Fiber, Stainless Steel, wood filled or any other metal filled filaments, this will greatly improve the life of your nozzle.
ID: 11955   Your Price: €18.00
Small Image
Add to Cart
Quantity On Hand: 1
Brand: E3D
Made from a hardened tool-steel base, they are then Nickel plated to maintain hardness at elevated temperatures, and have a WS2 coating applied to provide the nozzle with reduced stick properties. Rated to a maximum temperature of 500°C, Nozzle X prints every printable material*, from PLA all the way to Carbon Fibre-filled PEEK without wearing.
ID: 11960   Your Price: €42.34
Small Image
Add to Cart
Quantity On Hand: 5
Brand: Adafruit
The latest from Feather family, this one is based on Raspberry Pi's RP2040 microcontroller, a dual core 32-bit ARM Cortex M0+ @ 133MHz, the same one Raspberry Pi Pico uses. It can be programmed using CircuitPython, MicroPython or C/C++ (Arduino IDE support is recently added, VS Code can be used too).
ID: 11948   Your Price: €19.35
Small Image
Add to Cart
Quantity On Hand: 6
Brand: Adafruit
This is definetly the smallest RP2040 board, using the same microcontroller as Raspberry Pi Pico - dual core 32-bit ARM Cortex M0+ @ 125MHz had to be mounted on the back side to fit on the board. It has only 13 GPIO pins, but four of them are 12-bit analog inputs and all of them are PWM outputs. It can be programmed using CircuitPython, MicroPython or C/C++ (Arduino IDE support is recently added, VS Code can be used too).
ID: 11950   Your Price: €15.26
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Adafruit
Some microcontrollers, like the ATmega328, have built in EEPROM, but some, especially ARM Cortex's, don't. That's where this petite Adafruit 24LC32 I2C EEPROM Breakout comes in to help! With 32 Kbit (4 KByte) of storage, and handy chainable Stemma QT connectors, it's just the right amount of simple I2C-controllable storage. Since its external to your microcontroller, uploading new flash memory won't wipe the data from this chip.
ID: 11951   Your Price: €5.84
Small Image
Add to Cart
Quantity On Hand: 8
Brand: PrimaCreator
PrimaFIX works with the most common materials on the market such as PLA, PET-G, ABS, Wood and Flex. When you use PrimaFIX you should do so with a printer that has a heated build plate as the active substance in PrimaFIX activates when the temperature rises above 40 degrees.
ID: 11921   Your Price: €10.50
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Adafruit
When connected to your microcontroller it can detect simple gestures, return the amount of red, blue, green, and clear light, or return how close an object is to the front of the sensor. This device uses an I2C interface and STEMMA QT/Qwiic/easyC connectors, so it's easy to wire up and use. Works with both 3.3 and 5V microcontrollers.
ID: 11872   Your Price: €12.50
Small Image
Add to Cart
Quantity On Hand: 4
Brand: Adafruit
This brakeout bouard is general purpose USB to GPIO, SPI, I2C - it let's you communicate with sensors, displays etc. directly from your computer, no need for Arduino programming, just writa a simple Python script and run it on your Windows,Linux/mac PC. It even has GPIOs to read or write to LEDs, switches and buttons. This is a new version with USB-C and STEMMA QT/Qwiic/easyC connectors.
ID: 11874   Your Price: €23.40
Small Image
Add to Cart
Quantity On Hand: 16
Brand: RobotDigg
Neoprene rubber fiberglass open ended GT2 belt reinforced with nylon cloth tooth surface, 2mm pitch, 6mm width, sold per meter (max 10 m continuous roll).
ID: 11875   Your Price: €4.00
Small Image
Add to Cart
Quantity On Hand: 13
Input voltage 4-40V, output voltage 1.25-36V, max 8A (max 5A recommended for continuous draw), max power 200W, switching frequency 180KHz, efficiency 94%, LED display for output voltage, dimensions 64x47x28 mm.
ID: 11883   Your Price: €7.80
Small Image
Add to Cart
Quantity On Hand: 2
Brand: PJRC
The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory than the 4.0, and two new locations to optionally add more memory. The Teensy 4.1 is the same size and shape as the Teensy 3.6 (2.4in by 0.7in), and provides greater I/O capability, including an ethernet PHY, SD card socket, and USB host port.
ID: 11845   Your Price: €60.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: E3D
Original E3D hotend kit that comes with Prusa MK3(S), featuring a Prusa specific heatbreak with a custom internal geometry, this is a drop-in replacement with connectors, but without the Bowden tube.
ID: 11833   Your Price: €78.97
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Raspberry Pi
Raspberry Pi Pico is the first product built on silicon designed in-house at Raspberry Pi (“Raspberry Silicon”). At its heart is RP2040, a Raspberry Pi-designed chip, which features two ARM Cortex-M0+ cores clocked at 133MHz with 256KB RAM, 26 GPIO pins, and a broad range of interfacing options. This is paired with 2MB of on-board QSPI Flash memory for code and data storage.
ID: 11805   Your Price: €5.50
Small Image
Add to Cart
Quantity On Hand: 7
Brand: LilyGo
Development board based on ESP32 with addition of SIM800L module and LiPo battery connector, in combination with low sleep current makes it perfect for outdoor use. Comes with non-soldered headers and flex GSM antenna.
ID: 11746   Your Price: €44.00